Showing posts with label motorcycle. Show all posts
Showing posts with label motorcycle. Show all posts

Saturday, March 17, 2018

Ten Thousand Miles

The day I bought the bike (bottom), and 10,000 miles later (Top).


Yesterday, I passed a milestone, 10,000 miles on my motorcycle. Just under two years ago, I decided to learn to ride, and almost as soon as I started, I nearly quit.

I got thrown off the bike in day one of classes and scared the hell out of myself, and my instructors. That night I made the decision to finish the class, get my license and become a competent rider. Only then would I allow myself to quit riding IF I decided it wasn't for me. I would not let fear be the deciding factor.

Twenty one months ago I bought my bike and began riding daily. First in parking lots, then the mile and half to work, then longer. The first time on a highway above 35 mph, the wind, the speeding cars, the huge trucks, was terrifying. Now its routine.

I ride alone, I didn't have buddies or a club to ride with, so it was a few months before I felt confident enough to venture OTP. By the end of the summer I took my day trip, 200 miles. There's a special kind of courage to wonder out into the unknown alone. You have to have confidence in yourself that you can handle whatever comes your way.

I still ride every day. Every step out my door is preceded by the question: Can I ride the bike? Rain, sub freezing temps and the need to carry anything that won't fit in my backpack are usually the only things that answer that question with a "no."

Now I've done ten thousand miles! (On a bike that only saw 2,000 per year before I got it.) Riding through the steep hills and curves of the North Georgia mountains yesterday, still gave me moments of anxiety and challenge. Finding the right gear, leaning a little more, remembering to brake before the curve, NOT in it, managing front and rear brakes -- Riding take thought and purpose and skill.

But unlike two years ago, I didn't have the terror in the pit of my stomach. I knew that if I went down, I would survive. Ego, and probably body, bruised, but I could handle it, because I'd handled everything the road had thrown at me for 10,000 miles.

I give myself permission to quit riding now.

But I choose to continue anyway. Its who I am now, its a way of life for me now.

I'm also reminded now, that I'm entering my third year of riding -- The most dangerous years. Riders in their third year are the most likely to have an accident, more than cautious newbies, and far, far more than seasoned vets who continue on beyond year three.

I told myself, when I began, that I would remain cautious through this year, that I would not let hubris bring me to tragedy.


I see other riders in shorts and t-shirts, in minimal helmets, no gloves, etc. I feel the heat in the summer and think it would be great to go without a jacket, that my boots are thick and hot -- That I don't look "cool." But I also know the cost of a small mistake without protection can be huge, and that even if I do it all right, someone else might hit me, or a mechanical failure could bring me down hard.

I ride to feel alive, I do not want to die doing it... Or get maimed or crippled. I realize I always run that risk, but there's no need to multiply.

So I enter my third year of riding with a renewed sense of purpose to my riding. To get better. Be more aware, become more skillful, to push my limits more.

And I ride on.

Monday, March 12, 2018

Handlebars: Take 2!


Phaedrus got some more upgrades yesterday.

When I first bought my motorcycle, a 2004 Honda Shadow VLX 600, I knew I'd be making changes. One of the first things I did was to take pics and work up what the natural angles and lines of the bike were.
Follow the pink line, that's the natural visual spine of the bike. Notice how the original bars and mirrors stick way above? Ugly!

The line from the seat, over the gas tank to the top of the speedometer (the highest natural point on the bike) looked pretty good, but the original handlebars, and especially the mirrors just stuck way up and shattered the natural lines. They had to go.

After a minor involuntary dismount, the handlebars got bend and it was a quick swap to low-profile drag bars. Then came the electronics upgrade with new control buttons, internal wiring, a Motogadget M-unit and a new custom (by me) wiring harness. All this looked a lot better.

But those mirrors. Ugly!

Not to mention cheap. At the time I wasn't ready to shell out for high quality mirrors, and didn't want to waste money on mid-range that I knew I'd be replacing. So I bought a pair of cheap ($15) mirrors. After about 3000 miles the plastic on one cracked and it wouldn't stay straight. I bought another set. Then the glass fell out of another at 60 mph.  Four thousand miles later, another cracked in the same place.

Time to get on with the upgrades.

The drag bars were cheap steel. This time I upgraded to high quality, thick walled aluminum street bars, with about a 2" rise.

To keep the natural lines of the bike, I knew the mirrors would have to under mount, so I got a pair of Oberon bar-end clamp ons.

I never liked the stock turn signals, which are big cruiser style. I always have intended to strip the bike down to a bobber style, with minimal accessories, so I really wanted to minimize the signals. Motogadget M-blaze LED bar end signals are ideal. The function as front and rear signals, plus as marker lights, and look like part of the handlebars, so all the other signals can go!

To finish it off, I needed new grips to accommodated the bar-end signals, so I got a pair of Motogadget rubber grips. They make metal ones, but I prefer the comfort of rubber, plus the insulation between my hand and the bar in winter helps a little with cold hands, and they're 1/5th the price.

Since I was doing wiring, I disconnected the power by pulling the main fuse. Its easier to get to than the battery cables.

This whole exercise also served as a test of the wiring harness I'd built and installed last year. Pulling the old bars was simple: I removed the body panels in front of the tank to expose the wire connections. Disconnected and labeled all the connectors. When I rewired the bike previously, I used nylon OEM style connectors, which made this supper easy. Then dismount the levers, and unbolt the bar from the risers. It took maybe ten minutes.

I removed the original turn signals, front and back. They'll go on Ebay to recoup some of my expenses. Bye-bye!

Then I mounted and test fitted the new bars, making sure to carefully mark everything to make sure it all went back exactly where I wanted it later. Measure twice, cut once.

Taping and marking where the bars meet the risers makes sure that every time I take the bars off, I can put them back exactly how I like them.

One mistake I made with the drag bars was positioning the buttons, they weren't exactly were my thumb naturally went. Since they depend on holes in the bars, I wanted to make sure I got them perfect this time.

With the bars mounted and positioned exactly how I wanted it, and taped and marked to ensure I could get it back there, I installed the grips and throttle assembly, making sure to allow enough space for the mirror clamps. I was careful to allow about a small gap between the throttle grip and the mirror clamp, to ensure the throttle didn't stick.

With everything in place, I put a piece of tape roughly where I thought the buttons should go and gripped the handlebars in riding position. Then with my eyes closed, I extended my thumb to touch the tape. I marked the tape at the middle of my thumb top to bottom. That would be the vertical center of the button hole, the natural position of my thumb.

Grips and mirror clamps installed, and the wiring holes marked for ideal position based on my natural thumb position.

Then I marked the left/right center by measuring to allow for the full width of the button housing and to the natural center of the pad of my thumb where I press buttons. All this ultimately put all the buttons in comfortable position.

Drilling the aluminum bars was much easier than the steel ones. I started with a 1/8" pilot hole, then stepped up with progressively larger drill bits to 5/16". I drilled both holes while the bars were mounted.
Wiring whole drilled.
I also marked the center top of the handle bars as mounted, and made a mark on the bottom end of each side to show the lowest point when mounted. Then I removed the bars.

The exit whole for the wiring needs to be in the center of the bottom of the bars. I used the marks I made while they were mounted and located the bottom center. I drilled three pilot holes, and progressed up again until 5/16" and all the wholes formed one slot. Wiggling the drill bit back and forth a bit chewed away excess metal to help make a smoother slot.

Finally, I cleaned up all the drill holes with a roto-tool to remove any burs, and smooth the sharp edges that would chew up the wires. The last thing I want to do is have wires shorting out from rubbing on the metal edges. 

Thne it was just a matter of routing my existing wiring from the other bars into the new bars. I used a left over piece of wire and tape to fish the lines through and that was done.

Then came the M-Blaze bar end signals. 

Motogadget's instructions are pretty clear. Before installing them, I used heat shrink to wrap the wires where they exited the bars as an extra layer of protection against abrasion, then installed the M-Blazes.

M-Blazes are sold individually as left or right side, and the Motogadget logo needs to face up when they're installed. If you look closely, you can see that they have two LEDs facing front, and one facing the back when installed correctly. 

Now back to the bike for another test fit. I wrapped the M-blazes in masking tape to ensure I didn't scratch them while working. 

Using the tape markings, I mounted the bars again and checked the routing of all the wiring. 

This time, I was able to find some black vinyl tubing, which gives a way more professional look to the wiring than wrapping them in electrical tape. Also, since the wires can slide easily in the tubing, they're more flexible and should have less stress on them. 

I decided to route the M-blaze wires in the tubing with one set of control wires, and the other side separately. Cut them to length, and install the nylon connectors I'd used before and they were done!

My custom wiring harness made the whole thing easy! I took a lot of time and effort to think ahead when I built it, and now I feel vindicated. I could have run wiring straight from the M-Unit, all the way to the buttons, in a continuous single piece, but I assumed I'd need or want to remove the bars, or replace broken parts eventually, so it made sense to add connectors. Glad I did. 

I rehung the clutch and brake levers, reconnected the throttle cable and reconnected the M-unit. The moment of truth: turn the key and test each button. Everything worked right off the bat.

It works!

Then came time to mount the mirrors. The go on easy enough and I thought I had them where I wanted them. It was raining out, plus I'd just installed new grips, so I decided to wait until morning to ride and see. Since I used WD-40 to help slide the grips on, I knew I need to give them at least over night to set up.

Left side - Now to figure out how to get rid of the mirror mount on the clutch lever?

Right side.
Clean look, and the under-mount mirrors make riding feel more open, nothing obstructing my view.

Nice and clean, no bulky turn signals.

Profile. The natural line from the bottom of the seat all the way up to the bars is clean. (Need a new seat, though!)


A little reprogramming of the M-unit to make the M-blazes function as marker lights, too (10% brightness) and its done. 

The whole process took me about 4 hours. The simple wiring harness and nylon OEM style connectors made a huge difference in how easy everything was. 

I'm about out of things to work on before getting serious about the body work. With the electrical and controls finished, and the lighting upgraded, plus velocity stack and pipes wrapped the next move is really removing the rear fender and replacing it with the seat to make it a bobber. That will mean cutting down the front fender to match and getting a paint job. Guess I need to start saving some cash!


Thursday, August 17, 2017

Suches Loop and Unexpected Challenges

At Neels Gap, GA, almost finished with the Suches Loop, before I got really challenged.
Yesterday I passed 7000 miles of riding since I bought my motorcycle last year. I guess 7000 isn't really a milestone, but I did pass it while on a day trip to Suches Loop in the north Georgia mountains. The Loop is 11 miles of winding mountain roads that involves 318 curves, its sometimes called the "Georgia's Dragon's Tail."

I had the day off, and the weather was looking perfect, so I took the opportunity to drive the two hours north of Atlanta to experience the loop for my first time. I went solo, as always, I don't have any close friends in Atlanta that ride. Heading out solo on a motorcycle for any distance away from home always produces some anxiety. But it also creates a real feeling of accomplishment when you get home. 

I was a little anxious about this trip. Curves are one of the funnest parts of riding, but also can be the most challenging, especially when faced with back-to-back curves, sloping roads, blind curves around cliffs and through woods, long drop offs, narrow roads, down hill sharp curves, spots of gravel and whatever else the world wants to throw at you. Driving a bike through such roads takes focus and really test the skills of an inexperienced rider. Which is what I was looking for. 

Despite the perfect weather forecast, I did decided to take along my chaps and a rain liner for my Kevlar mesh jacket (it provides protection in a slide, but no protection from rain without a liner). It was a good call.

About 30 minutes from my destination, in the middle of nowhere, under mostly blue skies, a cloud decided to open up and dump buckets on me. Fortunately, I could see it coming about a half mile off and was able to pull off on a side road under a tree for some shelter. I pulled on my rain gear and saw blue skies ahead, so I pulled back out onto the four lane state road and continued on. 

I hate riding in rain. I avoid as much as possible. Besides just being uncomfortable, its scary. Helmets don't have windshield wipers, so visibility is impaired along with tire traction, and braking becomes far more dependent on the less powerful rear brakes. I've gotten caught out in the rain a few times, but only on city streets. The worst was in stop and go traffic, where I basically just got soaked for an hour. This was my first time riding on a highway at speed in the rain. Fortunately, traffic was light and the road was long and fairly straight.  

A few minutes later, the rain stopped and I kept riding until I was dry. Challenge faced and conquered! On to the curves!

I stopped for gas and headed into the mountains, north of Dehlonega, GA. The Appalachian Trail passes through this area. Its mostly national forest and park, lots of green trees, parting for occasional overlooks -- and LOTS of curves. 

The first stretch wasn't bad. I arrived at Two Wheels of Suches, a burger joint and camp ground for bikers only. What I didn't know was that the restaurant was only open Friday through Sunday, so I wasn't going to get the burger I had planned on. Having missed my chance for lunch in Dehlonega, I opted for a soda and candy bar from the gas station across the road and figured I'd get food after finishing the loop. There really weren't any other options. 

I headed up Wolf Pen Gap Road, the heart of the loop. This is a well maintained, if narrow, two lane road where the curves come fast, with banked roads, steep drop offs, switchbacks, steep dropping curves and lots blind curves. It was challenging, constantly managing the brakes and shifting up and down between 2nd and 3rd gear to manage speed and power as I went up hills, then engine braked on steep declines. 

One of the most critical skills of motorcycle riding is managing brakes and turning. Bikes have separate front and rear brakes, which affect the handling of the bike differently, and which must be handled differently in the event of a skid. Braking and turning both require increased traction, and tires only have so much traction to use. You cannot brake hard while turning, that's a good way to wreck. One of the cardinal rules of motorcycle riding is brake before the curve, accelerate (slightly) through the curve. Needless to say, coordinating both brakes, gears and throttle through constantly changing directions and elevations tests ones ability to keep it all upright. 

Add in the distraction of cliff faces and long drop offs, plus on coming traffic and you have another issue: Target fixation. One truism of riding is that the bike goes where you look. If you get fixed on looking at something that scares you, like an on coming car as you go around a curve, your body unconsciously tends to steer the bike toward the car... Or off the cliff, or where ever it is your mind and eyes have fixated.  This is the mental, and emotion challenge, of riding something like the Suches Loop. In my opinion, its the more critical part of the equation. You must be in control of your mind.

I'm proud to say I managed it all, including a few unexpected things, like spotting a gravel patch at the apex of a downhill set of switchbacks, which I had to navigate around at the last second while avoiding an oncoming car that was very close to the yellow line, with a drop off on my right. A scary moment, but I was impressed with how calmly and smoothly I handled it. Of course, my instant of self-congratulations was short lived because I had to immediately lean the bike the other ways and enter the next curve. Focus.

At the end of Wolf Pen Gap Road, I turned south onto Georgia 19, which is still a curvy mountain road, but wider (three lanes in some places) and most of the curves are not as intense. Following this up hill, I finally stopped at Neels Gap, the top of the mountain, for a scenic over look and to stretch my legs and hips. 

The view from Neel Gap, GA
From there, I figured it was relatively easy riding to the bottom and on to lunch. I head down through more curves. But those fluffy clouds had other plans, and I found myself looking down hill, into steep declining curves on fairly new (read "slick") black top as rain began to fall.

It was the kind of rain that you see like a curtain crossing the road ahead. Only I didn't see it until I rounded a curve and it was right there, and I didn't have time to stop. I found a spot to pull off under a tree where it seemed a little dryer to decide what to do.

Decision time: Wait it out, or make for the blue sky in the distance.
I had two choices, wait it out under the tree (which wasn't providing much protection), or brave the wet, curvy mountain roads to try to get out from under it. I could see blue sky not far away, but with all the switchback on the road, who know how far the drive actually was?

I decided to ride and face my fear. I knew the real risks were higher than on dry road, but I also knew they were not as high as my anxiety riddled brain was screaming. I had learned, and had some practice, with rain riding techniques and the roads were mostly free of other cars, so I set out.

Ten minutes or so later, I was on dry pavement that hadn't seen a drop all day. I had faced the challenge and over come it.

Challenges come in different ways in life. Riding a motorcycle, like many other things, is objectively a skill that anyone can learn. Taken in progressive steps and with practice, the skill can be mastered. But the real challenge is overcoming your fear. Your mind gets filled with images and ideas of everything that can go wrong, and you think about that, instead of what you need to do to be safe.

I chose to ride the Suches Loop to challenge my fears. I knew I was capable of riding curves. I wasn't trying to take them at full speed or prove what a bad ass I was. I just wanted to prove to myself that I had the skills and experience to take curve after curve after curve, of all variety of sizes, slopes, lengths, diameters, etc. And I did, the small fears of falling, of skidding, etc, that I feel every time I get on the bike were still there, I just had to push them down and focus on the task, like I do every time.

But the unexpected challenge of rain... That brought up a whole other level of fear. I would not have faulted myself if I decided to wait it out. It wasn't what I had set out to do, I had not mentally prepared myself for it, and it wasn't "do or die." I 'm glad I decided to face that fear, too.

There are challenges in life that we choose, like riding the Loop, and there are those life chooses for us, like riding in the rain. But a challenge is a challenge, whether we choose it or not, it is faced the same way: with courage and thought. Courage to acknowledge your fear, and thought to navigate the challenge safely.

The more challenges I set for myself in life, the more easily I find I can overcome the ones life throws at me. And that is how I create an amazing and interesting life for myself.

Tuesday, April 18, 2017

Motogadget M-Unit Installation on a Honda Shadow VLX

For my first ever adventure into wiring a motorcycle I decided to install a Motogadget M-Unit into my 2004 Honda 600 VLX.  It isn’t a glamorous bike, but its mine. Over the next few months I will continue on with other more noticeable changes, but since its my only bike, and I would prefer not to have it down for weeks or months at a time, these changes will be done piecemeal.

Because of this approach, it became clear that the first thing that needed to be done was upgrading the electrical system to accommodate new lighting and controls. The M-unit offered a very elegant and simple way of doing this, which to me, a total novice, seemed well worth the $300 price.

There are some forums dedicated to the 600VLX,but  it seems very few owners are interested in doing the kind of changes I want, or at least none that post. What posts I could find about wiring were pretty simple – The most complex issue was dealing with installing LED turn signals on the harness which wasn’t designed to accommodate them. All this meant that to install the M-Unit, I was pretty much going to have to figure it out on my own.

The M-Unit is designed to simplify wiring and can, apparently, work very when building an entire harness from scratch. However, going all the way to scratch was beyond the scope of what I thought I wanted to do (In retrospect, having accomplished what I have and learned as much as I have, I will start from scratch next time.)

What I’m going to attempt here is to break down, piece by piece, how to integrate an M-Unit in the a Honda 600VLX wiring harness,  keeping all the functionality of the original system, while adding the functions of the M-unit and removing the bulky and ugly stock controls. For simplicity sake, I’m going to use the OEM wiring diagram as reference and simply work my way around it, clockwise, item by item, and explain what to do with it. After which, I will discuss the new wiring added for the M-Unit and new controls.


NOTE: When I say “Cut and Cap” I’m saying a wire is not needed, and can be removed. If you want to open up the wiring harness and removed all the excess wires, like I did, do this carefully. Several wires branch off to multiple items. When removing a particular wire from a particular item, trace it back to the main wire of the same color where you’ll find the soldered splice. Do not cut the main wire, only remove the spliced on piece you don’t need any more.

My understanding is that many Hondas of this type have very similar harnesses, so a lot of this should translate. I hope you find this helpful.  Here we go!

Mounting the M-Unit: Under the seat, there is a black metal brace, on which is mounted a black cube – The Turn Signal Relay, which isn’t needed any more, so getrid of the relay, and mounted the M-Unit to the metal bracket, by drilling two holes in it. Easy.

At the top end of the Unit, I attached a ground wire and grounded it to the frame with a self-tapping screw (I think the metal plate could have served as a ground, but I felt a wire to the frame was more certain).

The M-Unit mounted and grounded where the turn-signal relay used to be.


THE OEM HARNESS

Ignition Switch (Key): Three wires: Red leads to the M-Unit Positive power input screw on the lower right. Red/black goes to the M-unit LOCK input (I soldered this wire to a smaller gauge wire to plug into the M-unit). Cut and cap the Blue/Orange wire, you won’t need it.

REAR LIGHTS (Tail, brake, turn signals and license plate): Disconnect all these connectors. If you want to reuse the nylon OEM connectors, cut the wires a few inches on the main harness side to attach to later. If you’re going to install new connectors or simple wire directly to the existing wires, cut them on the non-harness side of the connector.

Cut the three wires leading into the tail/brake light connector (Green, Brown, and Green/Yellow), a couple inches on the main harness side of the connector. Splice them all together into a single wire, and attach it to the M-Unit BRAKE output.

When programming the M-unit, set it for a single-wire brake system (LED or light bulb, which ever you have) and the tail/brake lights are all set.

Rear Brake Switch: Both brake switches are wired together with a Green/yellow wire. From the connector there is a black wire that goes to ground, leave it. Follow the Green/Yellow wire to where it leads to the tail/brake light connector (which you probably already cut), before it reaches the tail/brake light connector, cut it and plug it into the M-Unit BRAKE input.

Basically, what you’re doing here is placing the M-unit between the brake switches and the brake lights, by cutting the Green/Yellow wire and attaching switch end to the input and the lights end to the output.

Fuse box:  Remove the box and toss it, you don’t need it anymore. Four wires lead out from the connector: The Black, Black/brown and Blue/Black wires all attach to the M-Unit AUX output (which is a solid state fuse box) by soldering them all to a single wire. The Black/Red wire is cut and capped, its not needed anymore.

Main Fuse/Starter Solenoid: Four wires. The Red wire connects to the M-Unit at the Positive Power input screw, along with the Red wire from the Key Ignition. The Yellow/Red wire plugs into the M-unit START output. The other two, (Red/White and Green/Red) stay as is, leading to the Regulator/Rectifier.

Regulator/Rectifier, Alternator, Ignition Pulse Generator, Ignition Control Module: Leave these.
Turn Signal Relay: You removed this when you installed the M-Unit. Cut and cap all three wires. DON’T wire them to each other, cap them off individually.

LEFT HANDLE BAR CONTROLS:  The plan is to lose the whole bulky button housing. The only two wires to keep are the Green/White and Green Red wires, which connect to the clutch switch.  Everything else gets cut and capped (Drk Blue, Blue/white, Green, Orange, gray, Lt Blue, Black and Black/Brown).

NOTE:  If you choose to remove the clutch wires too, all that happens is you can’t start the bike with just the clutch pulled, the gear box will have to be in neutral.

Dimmer Switch: This feeds low power to the turn signals, so they are also marker lights. I plan on switching to 2-wire LEDs anyway, so I discarded this all together.

NOTE: The M-unit does have a programmable setting to fill this feature, however, the way I choose to wire, that program did not work. In my case, the OEM turn signals function only as turn signals.

Front Turn Signals: Disconnect both. Just like with the rear, if you’re going to reuse the connectors, leave yourself a few inches of wire to connect to, then cut and cap the remaining wires.

NOTE: I think, but I’m not sure, that if you solder the solid colored wires and the color/white wires from each turn signal together, creating a single wire, the marker light feature of the M-unit will function. But I have not tested this, since I really don’t care.

Headlight: The M-unit will now handle this. Cut the Blue and White wires a few inches back from the bulb connector. Attach new wires to each and run them to the M-unit, White to the LIGHT LO, and Blue to LIGHT HI. Green is your ground, you can leave it.

Indicator lights (Turn signal, Neutral and High-beam dash lights):  The single turn signal light and High-Beam indicator light will be powered through the M-Unit, so cut those wires a few inches back from the connector on the main harness side, and cap the remaining wires. Leave the Green and Lt Green/Blue wires.

Gauge Lights (Meter light, Temp Indicator, Oil Pressure): Leave these.

RIGHT HANDLE BAR CONTROLS: Even though we’re losing the bulky Starter/Engine Stop box, we need some of these connections. The Brown wire needs to be connected to one of the Black/brown wires. Do this either by keeping the other side of the connector where a small loop of Brown/Black wire makes the connection, or by cutting and splice the two wires together. The Black and Black/white wires need to be spliced together. If both of these loops are not made, the bike won’t start.

Cut and cap the Blue/White, Black/Red, Yellow/ Red. Keep the Green/Yellow and other Black/Brown wires (these are your front brake switch wires).

Side Stand Switch, Diode, Fan Motor Switch, Temp Unit, TP Sensor: Keep. The Diode, in case you’re wondering, is actually just a connector with a black cube plugged into it and wrapped in tape inside the wiring harness, if you don’t open up the OEM harness, you won’t even see it.

Horn: There isn’t a nylon connector here, just two black wires that plug into two tabs on the horn. The M-unit will control the horn, so you’ll need to connect one of these to the HORN output (by cutting and extending it) and the other to ground. One of the black wires does connect to a green wire if you follow it, that is the ground - leave it connected. Cut and extend the other wire to plug into the HORN output of the M-unit.

Neutral switch/Oil Pressure Switch: Leave these wires.

Ok, that’s it for the OEM harness. The M-Unit should come on when the key is turned and do its little LED cycle, ending with the LOCK and AUX LEDs lit. If you attach a temporary button to the START input and to a ground, the bike should start up. You should be able to also turn the head light on and off, and switch between high and low beams, using the same button at the LIGHT input. Same for the horn and each of the turn signals (but you might need to configure some things first.)

Connect a temporary button to the CONFIG input on the M-unit, and to ground, and follow the instructions to program the M-Unit for “one wire brake lights.” Once that’s done, the brake lights should work from both the front and rear brakes individually.

If all that works for you, you’re in great shape!

Now onto installing new control switches. I opted for the 5-button setup with the M-unit. The buttons are headlight, right and left turn signals on the left, and horn and start on the right (thanks to the M-unit, a double tap on the start button will kills the engine.)

THE M-UNIT CONTROLS HARNESS

All the buttons I used with the M-Unit are “Momentary” buttons, meaning they only close the circuit while being pushed, as soon as you release them, they spring back to the open state. The M-unit can also be programmed to work with “Japanese and European” buttons setups, which is what you’d use if you kept the stock controls (but why would you? They’re so ugly!)

All buttons have two wires, one which leads to the M-Unit, and one which goes to ground. You can ground your wires however you like, and you can connect all your grounds together to reduce clutter/confusion and save space. The M-Unit uses very little power for the buttons, so you can use very thin wires (I used 22 AWG).

Start Button: Run a ground, and plug the other wire into the START input on the M-Unit.

Horn: Just like the Start Button, a ground and one wire plugged into the HORN input.

Headlights: Same as above, input into the LIGHTS input (see a pattern here?)

Turn Signals: Again, one wire to ground for each button, and one wire each to the M-Unit inputs, TURN L and TURN R.

That’s its you’re buttons are wired. Seriously, look at the OEM wiring diagram to accomplish what you just did, its insane how complex it is without the M-unit!

M- UNIT LIGHTING HARNESS

This is a bit more complicated, but if you take it step by step, its pretty easy.

Headlight and High-Beam Indicator:  Splice into the Blue Headlight Wire, and connect it where the Blue wire was at the Indicator lights harness. Where the Green wire was on that harness, should be connected to ground. Now when you turn on your high-beams, you’re indicator light will come on too.

Turn Signals: This is the complicated one, so take it one step at a time. Both left and right are identical, so just repeat the procedure.

Top: The stock headlight and turn signal controls. Bottom: New Motone Mini-Buttons, much smaller, cleaner look, plus Blitwell Kung-Fu grips. .


A wire needs to leave the M-Unit from the TURN L or TURN R output and split into three wires. One will go to the front turn signal connector, and one to the back and one will be bridged to the indicator light on the dash.

 The second single wire from each of the connectors needs to go to ground from each signal itself.
Once this is done, the turn signals should work. To make the dash indicator work, attach a 1N4001 Diode to the third wire from each of the turn signal harnesses.  Be sure the direction of flow for the diode is away from the M-Unit.

 Then connect the other end of both diodes to a single wire which will connect the either the Lt Blue or Orange wire from the Indicator Lights connector. The other unused wire should go to ground. Now the indicator light should work when the turn signals come on.

That’s it! You should now have everything on the bike working. Program which ever features you want for the M-Unit.

Fully wired M-Unit. 
If you’re leaving your bike otherwise stock, there’s probably not a lot of point in doing all this. But, if you’re planning on future mods which will impact the electrical system, everything should be pretty simple now, just plug into the existing wiring and, if necessary, change the programming of the M-Unit to accommodate the new item.

Any new accessories (hand warmers, ground effect LEDs, etc) get spliced into the AUX power lines. Changes to the lighting just plug into the connectors you already have.

I hope this was helpful!

UPDATE: One the second day after finishing, I took my bike out for a night ride and immediately noticed that all the lights were brighter. The headlight, which I had planned on upgrading, is suddenly perfectly adequate, the turn signals are brighter and the dash indicator lights are actually annoyingly bright!

I'm not sure exactly where, but its clear that somewhere this new setup is saving a lot of juice which it can now devote to the lights.

Monday, March 13, 2017

This is How I Learn... Everything

I'm sure it hasn't escaped my one reader, who ever that is, that my motorcycle is at the core of this blog. It wasn't meant to be that way, but the two came into my life at about the same time, so there it is. If this blog goes on long enough, that may change, but until then...

I've been struggling with getting my carburetor tuned properly. Since wrapping the exhaust pipes and removing the airbox, there have been issues. Mileage has decreased significantly, there has been "popping" in the exhaust when I throttle down, power at first seemed to increase, but has since declined, power does not increase smoothly as I throttle up... I could probably go on, but those are the main things.

So I've been approaching it from different directions. Trying different tuning approaches from various sources, some solved some issues, but increased others. Nothing seemed to solve them all, which proper tuning should do. I initially looked at all the issues from the perspective of how they related to the air-fuel mix, but when that continued to yield unsatisfactory results, I changed my approach.

Last week, I took one obvious symptom, the popping, and searched to see what other issues it might arise from. It turns out, it could also result from a poor seal between the cylinders and the exhaust pipes. Since I've removed the pipes several times and never replaced the gaskets (they're supposed to be replaced every time! opps!) I ordered new ones. (BTW, exhaust is closely related to the air-fuel mix, so this would be a contributing factor that needed to be fixed in order to get tuning corrected.)

They arrived today, so I set out to replaced the old ones... Only there weren't any. Apparently, I either lost them without noticing (unlikely) or the previous owner didn't replaced them when they put after-market pipes on the bike. Whatever. I put the new gaskets in, and the popping stopped. So I tuned the carburetor following the factory recommended procedure, using a new digital tachometer I also bought (my bike does not have one of its own) and got better performance immediately.

But now there's another problem... maybe. When my initial problems began, one mechanic suggested increasing the main jet size, so I did. It didn't make sense at the time, but I knew less then. Now I know that that may be the cause of my reduced fuel economy, So I have to go back, remove the carb and reinstall the smaller jet.

All this trial and error is annoying, but I realize its also the way I tend to approach and learn everything I do. I jump in, tear things apart, fuck with what's working, generally mess it up, and try to get it back into equilibrium, only different from how it started. Its messy and time consuming, and I tend to go over somethings dozens of times. But in the end, I understand them, and know things I wouldn't have if I hadn't been so messy about it.

I've never been one to just accept what I'm told, I need to know why. If I wanted to be a mechanic professionally, I would got to school for it, and dig very deep into the how and why of all these things. I'm not going pro, so the time and money for school aren't in the cards. But, I am giving myself a useful education on this particular subject, and it will be followed by another.

I did this with carpentry, with bartending, with writing, working on my car (fuel injected, not carbureted, or I'd already know this stuff), and with scores of other things in my life. If you were to study my relationships, you probably see that the numerous long and short term relationships also fall into that pattern (not on purpose, but still probably true).

This is how I learn -- by doing. By getting dirty, and making it real and tangible, not theory.

Wednesday, November 2, 2016

New Lungs for Phaedrus


This morning I tackled the latest modification to my motorcycle, removing the airbox and replacing it with a velocity stack.

Before and after: Left: Stock airbox.. Right: airbox removed and velocity stack.
The first task was to remove the original airbox. The process was pretty simple, Just three screws held the cover on. Behind that was the filter, and two more screws holding the box in place. Once the main box was off, the black plastic tubing that filled the space between the top of the cylinder and the frame came out easily, it was only held in place by a hose clamp and friction apparently.

Airbox with the cover and filter removed. Only the two screws top center hold it on.

With the airbox removed, no screws to hold the tube in place behind it.

With the whole airbox assembly removed, the carb is exposed. The mounting plate under the gas tank is easily removed after the tank is off. Only two bolts attach the plate to the frame.
Getting the carb off was pretty straight forward. The gas tank had to be removed, which meant taking off the seat and petcock knob, then the one bolt that holds the tank on. I'd done all that before, and its not technically difficult, just takes a few minutes.

Under the tank a lot of hoses to remove. Like a lot of motorcycles, this one has things that aren't necessary to make it run well. The white triangle is part of the crank case breather,, which is overly complicated.

Before getting to the carburetor, I removed some unnecessary hoses. TJ Brutal Customs has a great video about what can be removed safely from this bike. Mine didn't have quite as much junk parts as some, probably because it wasn't originally sold in California.
The airbox and assorted hoses which no longer reside on Phaedrus.

With all those hoses removed, you can see straight down to where the carb connects to the manifold. Those two black screws are the hose clamps that hold the carb in place. The hose, immediately above them in this photo, is a coolant line that goes to the carb, which I rerouted.

With the extra hoses removed, getting my hands and tools inside to remove the fuel lines, coolant hoses, vacuum lines and throttle cables was much easier. There was a set of wires for the throttle position sensor to disconnect, that was the only wiring to deal with. 



I disconnected everything and pulled the carb off. The biggest problem was just working some of the hoses loose. 

With carb removed and the coolant hose rerouted.

This carb had two coolant hoses attached to it. One leading out of the engine into the carb, then a second from the carb to the radiator. Apparently this is to help warm the fuel in the carb (in theory), but in reality doesn't really effect much. Both the hoses are under pressure, so simply capping the nipples would not work (Coolant spraying out of the engine is usually a bad sign.) 

One source recommends using a screw inserted in the end of the hose (cut short) and a hose clamp to hold the screw in place. I may do that eventually, but I couldn't find a small enough hose clamp. Instead I cut the longer of the two hoses and ran it straight from the radiator to the engine, simply removing the carburetor from the routing. This will keep coolant flowing through everything else.

The velocity stack itself simply slides over the open air intake of the carb, and attaches with three recessed screws. Because of the increased air flow, the carb needed to be re-jetted. Again, TJ Brutal Customs has an excellent video showing how to install the new jets, and everything went exactly as described in the video. Since he does such a good job, I won't go into details, just follow his instructions.

Once the jetting was done, I capped off a couple vacuum and coolant ports. I also added TJ's long handled adjustment screw, since accessing the pilot adjustment on this bike is a real pain in the ass, even with the airbox removed. 

Once all that was done, I put the carb back on, which was simple since several hoses didn't need to be attached anymore. 

Adjusting the throttle cables was the biggest issue for me, mainly because I'd never done it before. It took me a bit to figure out I'd switched the two cables. Once I figured out that mistake, I had too much free play, I went from having no free play in the throttle to having too much. But eventually I got it adjusted.

A few more minutes to put the tank and seat back on, then came the moment of truth... After about 20 seconds of cranking (to get fuel through the drained lines) it started right up! 

I let it warm up while I cleaned up my tools, then took it for a spin. It ran a little rough at first, but after giving it time to warm up fully, and adjusting the new long handled screw on the carb it came right into tune. It runs fine, and seems to have a bit more power. There's now lots of room under the gas tank to move electronics to when I get around to rewiring it. 

My only issue is that proper tuning has the adjustment screw all the way in (at least I think its all the way in?) Which should actually make it stall instead of increasing the RPMs. So I might need to pull the carb off and change one of the jets (the kit includes 2 main jets, and 4 pilot jets), but I'm going to ride it for a bit and see how it goes. I would like to have some play in the tuning so I can adjust for altitude in the mountains, but I'm not going that far until spring, so there's time. 

UPDATE:
I tinkered with it most of yesterday, off and on, and never quite got it running right. After some emails with TJ, I woke up today and pulled the carb back off the bike, swapped out the pilot jet for a size up and took it out.

After warming up, and a couple turns of the air/fuel mixture screw it settled in nicely. I rode it around neighborhood streets, then out onto higher speed city roads, and finally for several miles of highway. It works great in all gears, wide open acceleration, cruising, and no popping or sputtering when I close the throttle down.

Thanks again to TJ Brutal Customs for a great product, great support with both videos and email assistance!

Wednesday, October 5, 2016

The Daily Scare - Or How I Learned to Stop Worrying and Love My Fear

"Do something every day that scares you."
 -- Mary Schmich

This is a lesson I've tried to apply in my life for years, but its so general, that it can be difficult to understand exactly how to employ it. For me, it took learning to ride a motorcycle to finally crystallize in my mind the best way to really do this.

When I first heard this years ago, I thought it meant doing something NEW that scared me everyday. The problem with that, is that I tended to look for big, new things I hadn't done before and that becomes difficult to keep up. Often time, big things, like skydiving for example, take a lot of time and effort to set up and follow through on. Its impossible to do something like that every day. 

This spring, I decided it was time I learned to ride a motorcycle, which is a big thing, not an every day level activity. It was something I'd long wanted to do, and had made various excuses to put it off for years. That time was over, the time to do it had come. So I signed up for an MSF class. I bought a riding jacket, complete with armor pads to protect myself, and ridding gloves. I had ankle height hiking boots, to protect my feet, so I was good to go. The class provided the helmets and motorcycles. 

The day of the class I was a little nervous, but mostly excited, and I expected to do well. I'd studied all my materials, read the course book cover to cover. I'm in good shape, generally athletic, and I got a good night's sleep. I was ready. 

The class consisted of classroom and practical riding on a closed parking lot. The classroom work was easy for me, I'd read the whole book, I knew the materials. The riding seemed easy at first, too. We started with starting the bike.

That sounds simple, but its a little more complicated than starting a car. Everything on a motorcycle comes with a higher price of failure. You're not protected by a metal cocoon with airbags and safety belts. You DO have several hundred pounds of metal and plastic between your legs capable of moving very quickly. Pop the clutch in a car and the car jumps and lurches and stalls and its embarrassing. Pop the clutch on a motorcycle and it could go rocketing off, possibly with you on it, out of control until it falls over, possible with you still on it. You could not only break the bike, bending the handle bars, scratching the paint, etc., you could hurt yourself or someone else very seriously. So you take extra steps with everything.

By the time we broke for lunch we were cruising around the lot in first gear, everything was fine. 

After lunch, things were getting more and more complicated, each skill building on the last. As we started up the bikes and moved out to line up for the next skill, I accidentally throttled the bike hard. I began to panic, but followed my instructor's first lesson, "The clutch is your friend." So I pulled the clutch. With the throttle open, the engine revved up high, screaming loudly and terrified me. The bike was still rolling, and I was panicked. I didn't think the clutch was working, so I let it out to try it again. 

Letting the clutch out with the engine racing on a 300cc sport bike is the perfect recipe for a wheelie, which is exactly what the bike did. The front wheel popped up, straight up into the air, throwing me off like a bucking bronco, and sending the bike careening forward into a fence. Fortunately, no one else was hurt. 

The incident scared the living shit out of me. My instructors nearly bounced me from the class, rightfully so. I was boarder-line, I was becoming a danger to myself and others. Nervously, I finished the day, having lost confidence in myself, I was re-thinking the entire motorcycle idea. Maybe this wasn't for me? Maybe I should stick to cars?

I showed up the next day and finished the class. Still anxious about the power of the bike, I was cautious about everything I did. I passed the written exam with a perfect score and got the lowest possible score on the practical riding exam to pass. Literally, one point lower and I would have failed. 

Humbled, I headed home. I stopped on the way home and bought a helmet. Leaving the class I wasn't sure I was going to continue riding, but spending a couple hundred dollars on a good helmet would force me to keep going. I made the decision that when I learned to ride safely and confidently, then I could quit. Buying the helmet was a commitment to that. I would prove I COULD do it, then not doing it would be a choice rather than a default.

A week or so later, new license in hand, I went to buy my first motorcycle, a used cruiser. Less powerful than the sport bike I'd learned on, but bigger. When I took it for a test ride around the owner's neighborhood, I did a similar thing to the accident in class. I lost control and ditched it in someone's front yard. No one saw me, the bike was fine, so I rode it back and bought it. 

I had a buddy drive it home a few days later. I was not ready for the 45 minutes on the highway. I'd never been out of 2nd gear before. 

Now I had a motorcycle. I'd been reading books about riding skills and safety for two weeks. I'd been listening to pod casts on the same subjects, and watching videos online.Now I had to put it into practice.

My first day out, I carefully rode it to a near by parking lot and began drilling the basic skills. Breaking, low speed cornering, clutching... Over and over and over. 

The next day, I woke up, had breakfast and headed out to do the same thing. The only road time the bike saw that first week was the mile and a half to the parking lot and back, at no more than 25 miles an hour. Then I began riding it to work and back, 2 miles each way. Then touring around town, even getting up into third gear. Every day I pushed a little harder. Every couple days I was back in a parking lot drilling skills. 

40 mph was the the next big scare. There seemed to be a big change in the amount of wind between 35 and 40. It was pushing me harder, buffeting me and bike, trying to turn me and push me off the bike. It was loud and scary. But I got used to it. 

Then I took it out on a little stretch of highway, up to 65 miles an hour! What was slow driving speed for me in my car, was terrifying on a motorcycle. I made it to my exit 3 miles down, turned off, and limped home on surface roads, too scared to go back the way I came. 

But the next day I did it again. Then again. Then again. Reaching out further and further every time, 5 miles then 10. Then came the day I was comfortable at 65, so I took it out for day trip. 220 miles round trip on highways and state roads.  By the end of the day I was exhausted from tension, but I'd also had those moments of bliss just cruising with my machine, the moments every biker rides for.

Over the course of the summer I made a point to ride every single day. My bike is 2004 model, and had 24,600 miles on it when I bought. The previous owners had put about 2000 miles a year on it. By the time I left for my end of August vacation, I had ridden all but two day since buying it and logged over 3,500 miles. More miles in a three months than that bike usually saw a year, and more than many riders ride in a year. 

I made a point to push myself every day. Not to the point of utter terror. I learned to sense my own tension, and to just touch on it a bit every ride. Maybe go a little faster, or further, maybe find a curvy road and practice riding curves. I learned to recognize when a specific skill made me nervous and increased my tension level, like entering a tight turn, the I'd head to a parking lot drill that skill over and over.

I learned to see situations that made me uncomfortable, like fast traffic, and spend a part of each ride in that situation until I got more comfortable. I learned to look for trouble, and spot potential problems and look for escape routes just in case, and practice specific skills that would help in those situations, like swerving and emergency stopping. 


Then the day came when I was riding to a friend's house. I headed up the on-ramp to the highway, twisted the throttle open, shifted up through the gears, merged into traffic, slide over a lane, then another, then another, until I was in the HOV lane, sliding past cars. Only then did I look down and see I was up to 80 mph, buffeted by wind, cruising in heavy traffic, around bends in the highway, and feeling fine. I was alert, aware, but not worried, not tense.

I had done something every day that scared me. It was the same thing, riding a motorcycle, but it was also always a different thing, a new challenge, a little faster, a little further, ride the highway, ride the curves, brake harder, turn tighter. I learned to sense my fear, and to use it as a guide. I learned to read it, to know when it was telling me "this is what you need to practice," and when it was saying, "back off, take a break."

Looking back, I've applied this approach to a lot of things in my life, but I didn't realize it. Now that I do, I can continue to apply it, in a conscious way, from now on -- Doing something every day that scares me. But I learned something else when I learned to acknowledge my fears and to be guided by them.

I learned that the feeling I got that guided me to work on my turning skills, is the same feeling I get in other situations in life, like when I need to apologize to someone when I'm mad. Well, not exactly the same, but similar. That's a fear, too, fear of being vulnerable, of admitting wrong, of setting myself up to be yelled at and shamed. Doing those things also falls under the category of "things that scare me."

Doing something that scares me everyday turns out to be easier than I thought, because every day I find things that scare me, maybe even the same thing that scared me yesterday. It doesn't have to be a big thing, or something I planned. I just need to acknowledge that I am feeling fear, anxiety, uncertainty, and then understand that feeling and figure out if its telling me to move forward and grow, or to slow down and not push too hard. 

Everyone can see the use of using fear to learn a new skill. Now I can ride a motorcycle with confidence, and I have the sense to know when I should take it easy, and when I need to practice, but the end result is easy for everyone to see. Its measurable, demonstrable. 

The other kinds of things, the little daily fears that I use to guide me now, are not so easy for others to see, but the changes following them has made in me are no less an improvement in my life and in my character. I'm more open, more forgiving, more loving, I'm friendlier. 

So I have learned to embrace my fears, to feel them, to question them, and to follow them. Every day I do something that scares me, and that is changing who I am for the better.